Compatible with the iPhone 7, the iPhone 8 and the iPhone SE 2nd Generation.
Clear, shatter proof protection with Power Support’s Shock-absorbing AFP Crystal Film Set for iPhone 7. Six shock absorbing layers shield your iPhone screen from bumps, drops, and hits. Engineered and produced in Japan our film absorbs and dissipates glass shattering shocks to your iPhone’s screen. Hard screens like tempered glass may resist scratches but its brittle nature makes it unable to resists shocks, causing cracks and breaking. In an Iron Ball Drop Tests a 110g iron ball was dropped 1.5 meters directly onto a glass screen protected by the Shock-absorbing AFP Crystal Film with no cracks or damage to the glass. The clear, high gloss film is extremely transparent and enhances the clarity and visual quality of the screen. The AFP hard, outer coating incorporates a new anti-fingerprint coating specifically developed to improve surface responsiveness, repel water and oil while protecting against scratches, dirt and dust. The anti-fingerprint coating does not entirely prevent finger prints, but, unlike inexpensive screen films, oils and dirt from your fingers do not adhere or penetrate the surface making the screen easy to clean. The AFP coating also resists most common oils and compounds found in make-up, body lotions, cooking and industrial settings so that they can easily be removed and cleaned off the film surface.
Six layers of protection.
Easy to Apply
Unlike some screen films that require an elaborate and messy application process or a special applicator operated by store personnel, Power Support’s Shock-absorbing AFP Crystal Film™ Set for iPhone 7 is easy to apply by yourself! Our Rip In Place (RIP)™ screen protector application technology (see instructions below) makes it easy to apply the film. Our film is not “glued” to the screen, but clings. This makes it easy to remove and re-attach the film or remove unwanted lint and dust during application.
The Shock-absorbing AFP Crystal Film™ Set for iPhone 7 clearly protects your screen’s surface from scratches, dirt and shocks while enhancing the image.
- Shock-absorbing & Shatter Proof
- 0.4 mm thin
- Scratch Resistant
- Easy to apply with Rip-In-Place™ technology
- 1 Shock-absorbing crystal film
- 1 Micro fiber cleaning cloth
- 1 Dust Remover
Rip In Place (RIP)™ screen protector application
Our Rip In Place (RIP)™ screen protector application technology is designed to help you cleanly and accurately apply the screen protector. You will notice there are two notches in the film's backing. This backing has been molecularly designed to rip in a straight line and produce no dust or fine particles. Now you can line up the screen protector and secure it in place before attaching the entire film on to the screen.
Always attach new Power Support screen protector film in a clean, dust free environment.
Using the provided cloth, carefully remove dirt and dust from the iPhone screen surface.
Remove the backing from the Dust Remover and apply the sticky side to the iPhone glass surface. Peel off the Dust Remover and lift off residual dust and dirt from the glass screen.
Pick up the film and find the two cuts or notches along the side of the film backing.
Remove the center portion of the film backing from the film to expose the adhesive.
Placing the adhesive side down align the film with the screen surface and slowly apply the center portion of the film onto the iPhone glass.
While holding down the center portion of the film, slowly remove the upper portion of the film backing while applying the film to the iPhone glass surface.
Finally, while holding down the upper portion, slowly remove the lower film backing and apply the remainder of the film to the glass surface. Press out any air bubbles as you proceed.
Trapped dust and air bubbles
Trapped air bubble can be gently pushed to the edge of the film with your fingers and the included micro fiber cleaning cloth. Most bubbles will work themselves out in 24 to 48 hours.
Trapped dust and dirt particles can be removed by lifting up the corner of the film closest to the dust speck. Use the enclosed film remover or use a piece of tape, such as scotch tape. Press the tape on the top of the film and carefully lift. Using another piece of tap lift the dust up off the screen or the back of the film.
To remove the film, slide the separately included film remover between the screen protector and the iPhone screen, lift and remove the screen. You may need to try different corners till you find one that you can lift.